PMK BumbleBee® High Voltage Differential Probe. ±2000V, 2m cable
The PMK BumbleBee® high voltage differential probe series offers industry leading performance up to 500MHz bandwidth for today‘s power device design challenges, especially those using wide bandgap devices, such as SiC and GaN.
The ±2000V, ±1000V, ±400V and ±200V differential and common-mode input voltage ranges makes BumbleBee® probes an ideal choice for designing and evaluating power circuits, such as switching power supplies, motor drives, inverter, IGBT circuits and frequency converters in the different voltage classes.
- Broadband 400MHz / 500MHz
- ±2000V, ±1000V, ±400V and ±200V
- High CMRR (Common Mode Rejection Ratio)
- 4-type attenuation (50:1, 100:1, 250:1, 500:1)
- Can be used with any measurement equipment with 50Ω input
BumbleBee® series probes have four adjustable input attenuation ranges allowing the user to select the voltage range needed to achieve the lowest noise and best possible resolution. The probe is compatible with any oscilloscope with a 50Ω input impedance and has a user adjustable DC output offset correction range of ±4V (output referred). All BumbleBee® series probes can be controlled from the controls located on the probe head or via remote control.
A PMK power supply unit is required. These are available with a USB interface and are optionally available with a LAN interface. Remote control of the probe is made possible by the power supply unit allowing:
- Automatic probe detection
- Save and load probe settings to enable reproducible measurements
- Free colour selection of the channel identifier to match the selected oscilloscope input
- Offset zeroing without entering values
- Changing the offset step size when using the probe manually
- Numerical input of the offset voltage to mask DC components in the signal, allowing the user more detailed insight into the signal without overdriving the oscilloscope's input amplifier
- Setting the desired division factor
- Dark switching of the entire keypad for use of the probe in dark chambers
- Keypad lock to protect against unauthorized access and thus against unwanted changes to the settings
- Activate / mute keypad buzzer for manual and remote operation
- Detection and counting of overvoltages or overdriven amplifiers with path detection
- Switchable continuous signalling (beep) when overvoltage (overload) is detected
- The software enables the use of PMK probes in semiconductor testers or in environments that are not accessible or dangerous for the user during operation.
The 1 channel battery pack power supply AP-01 provides >8h of portable and isolated operation, which allows the user the flexibility of where the probe can be used. The AP-01 supplies power only to the probe with no software remote control.
Models & Specifications
| Order number | Article | Attenuation | Bandwidth (-3 dB) | Input Voltage | Differential Input Impedance | Rise time |
| 880-102-501 | BumbleBee® ±2000V, 2m | 500 : 1 | 400 MHz | 2000V peak | 10 MΩ || 2.5 pF | 0.9 ns |
| 250 : 1 | 400 MHz | 2000V peak | 10 MΩ || 2.5 pF | 0.9 ns | ||
| 100 : 1 | 400 MHz | 2000V peak | 10 MΩ || 2.5 pF | 1.0 ns | ||
| 50 : 1 | 400 MHz | 2000V peak | 10 MΩ || 2.5 pF | 1.0 ns | ||
| 880-106-501 | BumbleBee® ±2000V, 6m | 500 : 1 | 400 MHz | 2000V peak | 10 MΩ || 2.5 pF | 0.9 ns |
| 250 : 1 | 400 MHz | 2000V peak | 10 MΩ || 2.5 pF | 0.9 ns | ||
| 100 : 1 | 400 MHz | 2000V peak | 10 MΩ || 2.5 pF | 1.0 ns | ||
| 50 : 1 | 400 MHz | 2000V peak | 10 MΩ || 2.5 pF | 1.0 ns | ||
| 880-107-501 | BumbleBee® ±2000V, 7m | 500 : 1 | 400 MHz | 2000V peak | 10 MΩ || 2.5 pF | 0.9 ns |
| 250 : 1 | 400 MHz | 2000V peak | 10 MΩ || 2.5 pF | 0.9 ns | ||
| 100 : 1 | 400 MHz | 2000V peak | 10 MΩ || 2.5 pF | 1.0 ns | ||
| 50 : 1 | 400 MHz | 2000V peak | 10 MΩ || 2.5 pF | 1.0 ns | ||
| 880-132-501 | BumbleBee® ±1000V, 2m | 500 : 1 | 500 MHz | 1000V peak | 5 MΩ || 2.5 pF | 0.8 ns |
| 250 : 1 | 500 MHz | 1000V peak | 5 MΩ || 2.5 pF | 0.8 ns | ||
| 100 : 1 | 400 MHz | 1000V peak | 5 MΩ || 2.5 pF | 0.95 ns | ||
| 50 : 1 | 400 MHz | 1000V peak | 5 MΩ || 2.5 pF | 0.95 ns | ||
| 880-137-501 | BumbleBee® ±1000V, 7m | 500 : 1 | 500 MHz | 1000V peak | 5 MΩ || 2.5 pF | 0.8 ns |
| 250 : 1 | 500 MHz | 1000V peak | 5 MΩ || 2.5 pF | 0.8 ns | ||
| 100 : 1 | 400 MHz | 1000V peak | 5 MΩ || 2.5 pF | 0.95 ns | ||
| 50 : 1 | 400 MHz | 1000V peak | 5 MΩ || 2.5 pF | 0.95 ns | ||
| 880-122-501 | BumbleBee® ±400V, 2m | 500 : 1 | 500 MHz | 400V peak | 2.5 MΩ || 2.5 pF | 0.8 ns |
| 250 : 1 | 500 MHz | 400V peak | 2.5 MΩ || 2.5 pF | 0.8 ns | ||
| 100 : 1 | 400 MHz | 400V peak | 2.5 MΩ || 2.5 pF | 0.95 ns | ||
| 50 : 1 | 400 MHz | 400V peak | 2.5 MΩ || 2.5 pF | 0.95 ns | ||
| 880-127-501 | BumbleBee® ±400V, 7m | 500 : 1 | 500 MHz | 400V peak | 2.5 MΩ || 2.5 pF | 0.8 ns |
| 250 : 1 | 500 MHz | 400V peak | 2.5 MΩ || 2.5 pF | 0.8 ns | ||
| 100 : 1 | 400 MHz | 400V peak | 2.5 MΩ || 2.5 pF | 0.95 ns | ||
| 50 : 1 | 400 MHz | 400V peak | 2.5 MΩ || 2.5 pF | 0.95 ns | ||
| 880-112-501 | BumbleBee® ±200V, 2m | 500 : 1 | 500 MHz | 200V peak | 1 MΩ || 2.5 pF | 0.8 ns |
| 250 : 1 | 500 MHz | 200V peak | 1 MΩ || 2.5 pF | 0.8 ns | ||
| 100 : 1 | 400 MHz | 200V peak | 1 MΩ || 2.5 pF | 0.95 ns | ||
| 50 : 1 | 400 MHz | 200V peak | 1 MΩ || 2.5 pF | 0.95 ns | ||
| 880-117-501 | BumbleBee® ±200V, 7m | 500 : 1 | 500 MHz | 200V peak | 1 MΩ || 2.5 pF | 0.8 ns |
| 250 : 1 | 500 MHz | 200V peak | 1 MΩ || 2.5 pF | 0.8 ns | ||
| 100 : 1 | 400 MHz | 200V peak | 1 MΩ || 2.5 pF | 0.95 ns | ||
| 50 : 1 | 400 MHz | 200V peak | 1 MΩ || 2.5 pF | 0.95 ns |
Power Supplies (order separately)
| Order number |
Article |
Mains | Output Current (max.) | Noise* | Channels | Output Voltage | Power | Immunity | |
|
889-09V-PS2 |
2ch Power supply for remote control with USB interface |
100-240 V AC, 47-63 Hz |
550 mA /Channel |
8 mV |
2 |
± 9 V |
20 W |
EN 60601-1-2 |
|
|
889-09V-PS2-L |
2ch Power supply for remote control with USB and LAN interface |
100-240 V AC, 47-63 Hz |
550 mA /Channel |
8 mV |
2 |
± 9 V |
20 W |
EN 60601-1-2 |
|
|
889-09V-PS3 |
4ch Power supply for remote control with USB interface |
100-240 V AC, 47-63 Hz |
550 mA /Channel |
4 mV |
4 |
± 9 V |
40 W |
EN 60601-1-2 |
|
|
889-09V-PS3-L |
4ch Power supply for remote control with USB and LAN interface |
100-240 V AC, 47-63 Hz |
550 mA /Channel |
4 mV |
4 |
± 9 V |
40 W |
EN 60601-1-2 |
|
|
889-09V-AP01 |
1ch Battery pack, >8hrs operation, no remote control |
700 mA DC |
1 |
± 9 V |
20 W |
||||
|
890-520-900 |
Probe connection cable 0.5 m ** |
||||||||
|
890-520-915 |
Probe connection cable 1.5 m |
||||||||
PMK BumbleBee Series Datasheet
